Angular Kinetics: Torque, Levers & Center of Mass
Find your center of mass two ways, balance a lever, and see why the same dumbbell feels heaviest with your elbow at 90°.
Overview
Force causes linear acceleration; torque causes angular acceleration. Torque depends on how hard you push and where and in what direction you push relative to the axis. The center of mass is the point about which the body's weight produces no net torque — the balance point. This week you will use torque balance to locate the COM, verify the lever principle, and quantify how joint angle changes the torque a muscle must overcome.
Learning objectives
- Calculate torque as force × perpendicular moment arm, with correct sign convention.
- Apply static equilibrium (ΣF = 0, Στ = 0) to levers and the human body.
- Classify first-, second- and third-class levers and compute mechanical advantage.
- Locate whole-body COM with a reaction board and with the segmental method, and compare them.
- Explain how joint angle changes resistance torque and required muscle force.
| Component | What you do | Time |
|---|---|---|
| Pre-lab | Torque, levers, equilibrium, center of mass; quiz | 20–30 min |
| Lab activity | Four 18-minute stations: reaction board, segmental photos, lever balance, elbow torque | 90 min |
| Lab report | COM comparison, lever verification, torque–angle curve, discussion | ≈ 90 min |
Pre-Lab Reading ≈ 15 min
1. Torque
Torque (moment of force, τ) is the rotational effect of a force about an axis:
| τ = F · d⊥ | Torque (N·m) = force × perpendicular distance from the axis to the force's line of action |
| d⊥ = r · sin θ | Moment arm when the force acts at distance r and angle θ to the segment |
| Sign | Counter-clockwise (+), clockwise (−) |
| Στ = I · α | Angular version of Newton's 2nd law (I = moment of inertia) |
| ΣF = 0 and Στ = 0 | Static equilibrium — not moving, or moving at constant velocity |
A force through the axis (d⊥ = 0) produces no torque, however large it is. That is why the moment arm, not just the load, decides how hard a joint has to work.
2. Levers
A lever is a rigid bar rotating about a fulcrum (axis). In the body, bones are levers, joints are fulcrums, muscles supply the effort force, and body or external weight is the resistance.
| Class | Arrangement | Body example | Mechanical advantage (MA = d_effort / d_resistance) |
|---|---|---|---|
| 1st | Axis between effort and resistance | Neck extensors balancing the head on the atlas | < 1, = 1 or > 1 |
| 2nd | Resistance between axis and effort | Calf raise (axis at the toes) | > 1 — favors force |
| 3rd | Effort between axis and resistance | Biceps flexing the elbow | < 1 — favors speed and range |
At equilibrium: F_effort · d_effort = F_resistance · d_resistance. Most human joints are third-class levers: muscles must produce forces many times the external load, but small muscle shortening produces large, fast movement of the hand or foot.
3. Center of mass
The COM is the mass-weighted average position of all body segments:
| x_cm = Σ(mᵢ·xᵢ) / Σmᵢ | Segmental method (also for y_cm) |
| x_cm = (S − S₀)·L / W | Reaction board: S = scale reading with subject (N), S₀ = board-only reading (N), L = distance between supports (m), W = body weight (N) |
Reaction board: a rigid board rests on a knife-edge at one end (the axis) and a scale at the other. When a person lies on it, taking torques about the knife-edge gives W·x_cm = (S − S₀)·L. The COM is the point where body weight's torque balances the scale's extra reaction torque.
Segmental method: digitize joint centers on a photo, locate each segment's COM using anthropometric fractions, then mass-weight them:
| Segment (proximal → distal) | Mass fraction of body | COM from proximal end (fraction of length) |
|---|---|---|
| Head & neck (C7 → ear canal) | 0.081 | 1.000 (at ear canal) |
| Trunk (shoulder → hip) | 0.497 | 0.500 |
| Upper arm (shoulder → elbow) | 0.028 | 0.436 |
| Forearm (elbow → wrist) | 0.016 | 0.430 |
| Hand (wrist → knuckle II) | 0.006 | 0.506 |
| Thigh (hip → knee) | 0.100 | 0.433 |
| Shank (knee → ankle) | 0.0465 | 0.433 |
| Foot (heel → toe) | 0.0145 | 0.500 |
Limb values are per side; both sides plus head and trunk sum to 1.000.
Segment COM coordinate: x_seg = x_prox + f·(x_dist − x_prox), same for y.
Before you come to lab
- Wear fitted clothing (joint centers must be visible in photos).
- Bring your laptop with Kinovea and Excel.
Pre-Lab Quiz ≈ 10 min
Short responses (submit to your LMS)
1. Explain why a biceps curl feels hardest near 90° of elbow flexion and easiest near full extension, using the word "moment arm".
2. Name a posture or movement where the COM lies outside the body, and explain why that is possible.
Lab Activity 90 min
Station rotation
4 teams of 5 rotate through four stations, ~18 minutes each. Each station has an instruction card and data sheet.
| Time | Team 1 | Team 2 | Team 3 | Team 4 |
|---|---|---|---|---|
| 0:00–0:10 | Briefing: torque sign conventions, how to read the reaction board, segment landmarks | |||
| 0:10–0:28 | A | B | C | D |
| 0:29–0:47 | B | C | D | A |
| 0:48–1:06 | C | D | A | B |
| 1:07–1:25 | D | A | B | C |
| 1:25–1:30 | Upload data and photos to the team folder | |||
Station A — Reaction board (whole-body COM)
Equipment: rigid board (≈ 2 m) with a knife-edge support at one end and a platform scale under the other; tape measure; body-mass scale.
- Measure L (knife-edge to scale contact) and record S₀ (board alone, N = kg reading × 9.81).
- Record each subject's body weight W and standing height.
- Subject lies supine with heels against a stop at the knife-edge end. Record S for: (1) arms at sides, (2) arms overhead, (3) knees bent to 90° with feet flat (hip and knee flexed).
- Test 2–3 subjects (different body types if possible).
Station B — Segmental method photos
Equipment: tripod-mounted phone, meter stick for scale, joint-center markers.
- Camera perpendicular to the subject's sagittal plane, whole body in frame, meter stick in the plane.
- Photograph the same subjects as Station A in: anatomical standing, arms overhead, and a deep squat (or a sport pose of your choice).
- Save the photos to the team folder. Digitizing is done in the report (Step 2). If time remains, start placing Kinovea point markers on the standing photo.
Station C — Lever balance
Equipment: meter stick, fulcrum stand, hook masses (100–500 g), spring/luggage scale.
- 1st class: fulcrum at 50 cm; hang 200 g at 30 cm from fulcrum; use the spring scale (pulling down on the other side) at 10, 20, 30, 40 cm. Record effort force.
- 3rd class: fulcrum at 0 cm; spring scale pulling up at 10 cm and 20 cm; resistance at 60 cm and 80 cm.
- If time remains — 2nd class: fulcrum at 0 cm; resistance at 20 cm; spring scale pulling up at 40, 60, 80 cm.
- For each, predict F_effort before measuring.
Station D — Elbow torque vs. angle
Equipment: dumbbells (2.5 and 5 kg), goniometer or phone angle app, tape measure.
- Measure the subject's elbow-to-dumbbell-center distance r and estimate biceps insertion distance (≈ 4–5 cm from the elbow; palpate the tendon).
- Subject holds the dumbbell isometrically with the upper arm vertical at elbow angles of 0° (hanging), 45°, 90° and 135° of flexion, 5 s each. Partner measures the angle.
- Subject rates effort (0–10) at each angle. Repeat with the second dumbbell.
- Optional: measure the perpendicular moment arm directly by dropping a plumb line from the dumbbell and measuring horizontal distance to the elbow.
Lab Report ≈ 90 min
⬇ Reaction board, 3 subjects × 3 postures · Segmental coordinates, standing · Segmental coordinates, arms overhead · Lever trials · Elbow torque, 2 subjects
Step 1 — Reaction board COM ≈ 10 min
Lay out one row per subject and posture: A Subject, B Posture, C body weight W (N), D height (m), E scale reading S (N), F board-only S₀ (N), G support distance L (m). Then add:
| Col | Header | Formula (row 2) |
|---|---|---|
| H | x_cm from feet (m) | =(E2-F2)*G2/C2 |
| I | COM (% of height) | =H2/D2*100 |
Expect ≈ 55–57% of height from the feet in the arms-at-sides posture.
Step 2 — Segmental COM ≈ 30 min
Template columns: A Segment, B–C proximal x, y, D–E distal x, y, F mass fraction, G COM fraction (rows 2–15, one per segment).
| Col | Header | Formula (row 2, fill down to row 15) |
|---|---|---|
| H | Segment COM x (m) | =B2+G2*(D2-B2) |
| I | Segment COM y (m) | =C2+G2*(E2-C2) |
| J | Mass fraction × x | =F2*H2 |
| K | Mass fraction × y | =F2*I2 |
| J16 / K16 | Whole-body COM x, y (m) | =SUM(J2:J15) ; =SUM(K2:K15) |
| K17 | COM height (% of height) | =K16/1.75*100 (use your subject's height) |
The mass fractions already sum to 1, so no division is needed. Digitize the standing photo (10 points: ear, C7/shoulder, elbow, wrist, knuckle, hip, knee, ankle, heel, toe; ≈ 10 min in Kinovea) and enter the coordinates in the template. A second posture is optional.
Figure 1. Stick figure: plot the digitized joint points as a scatter with lines, and the whole-body COM as a large red marker. Putting the photo behind the chart (plot-area fill, as in Week 5) is optional.
Step 3 — Lever and elbow torque ≈ 20 min
- Table 1. Lever trials. Columns: A class, B d_r (m), C resistance mass (kg), D F_r (N), E d_e (m), F measured F_effort (N); add G predicted
=D2*B2/E2, H % error=(F2-G2)/G2*100, I mechanical advantage=E2/B2. - Figure 2. Measured vs. predicted effort force (scatter with a 1:1 line).
- Table 2 / Figure 3. Elbow torque. Columns: A subject, B dumbbell mass (kg), C r (m), D biceps insertion d (m), E elbow angle (deg), F effort rating; add G torque
=B2*9.81*C2*SIN(RADIANS(E2))and H biceps force=G2/D2. Plot torque and effort rating vs. elbow angle (rating on a secondary axis).
Step 4 — Discussion questions ≈ 30 min
Answer the five required questions. Optional questions earn up to +3 extra-credit points.
- Compare reaction-board and segmental COM (standing) for the same subject. Which do you trust more? Give two error sources for each method.
- How far did the COM move when the arms were raised overhead? Explain the size of the shift using segment mass fractions.
- Did measured lever forces match predictions? Explain discrepancies (mass of the meter stick, friction at the fulcrum, reading the scale).
- At which elbow angle was resistance torque greatest, and did perceived effort follow the same pattern? Explain any mismatch (muscle length–tension relationship, changing muscle moment arm).
- The biceps force needed to hold a 5 kg dumbbell at 90° was many times the dumbbell's weight. Why is the body "designed" this way?
Optional questions (extra credit)
- For the squat or sport pose, where is the COM relative to the base of support? What does that mean for stability (preview of Week 10)?
- Give one rehabilitation or strength-training example where changing the moment arm is used to progress or regress an exercise.
Submission checklist
- Excel workbook: reaction-board calculations, segmental COM sheet (standing; second posture optional), lever and torque tables, Figures 1–3.
- Document: tables, figures with captions, discussion answers.
Grading rubric (50 pts)
| Criterion | Pts | Full credit looks like |
|---|---|---|
| COM calculations (both methods) | 15 | Correct formulas, % height, standing posture by both methods |
| Lever & torque analysis | 10 | Predicted vs. measured, MA, torque–angle relationship |
| Figures | 10 | Stick figure with COM, 1:1 plot, torque curve |
| Discussion | 15 | Compares methods critically, applies torque to exercise |
References
- Winter, D. A. (2009). Biomechanics and motor control of human movement (4th ed.). Wiley. Segment parameters adapted from Dempster, as tabulated by Winter.
- Urone, P. P., & Hinrichs, R. (2022). College physics 2e. OpenStax. openstax.org (CC BY 4.0) Chapter 9 (statics and torque).