Linear Kinematics I: The Countermovement Jump
Record a jump, track the center of mass frame by frame in Kinovea, and turn position data into velocity and acceleration in Excel.
Overview
Kinematics describes motion without asking what caused it. In this lab you will analyze the center of mass (COM) during a countermovement jump (CMJ) recorded in the sagittal (side) and frontal planes. You will extract COM displacement in Kinovea, export it as a spreadsheet, and calculate and graph displacement, velocity and acceleration.
Learning objectives
- Record frontal- and sagittal-plane video suitable for 2D motion analysis.
- Calibrate a video and track an estimated COM point in Kinovea.
- Export kinematic data and organize it in Excel.
- Calculate velocity and acceleration with the finite-difference method and plot all three variables against time.
- Identify the phases of the CMJ on displacement, velocity and acceleration curves.
| Component | What you do | Time |
|---|---|---|
| Pre-lab | CMJ phases, the position–velocity–acceleration relationship, video capture rules; quiz | 20–30 min |
| Lab activity | Film jumps, calibrate and track the COM, export data | 90 min |
| Lab report | Excel calculations, 3 graphs, jump height check, discussion | ≈ 90 min |
Pre-Lab Reading ≈ 15 min
1. Position, displacement, velocity and acceleration
Position is where something is relative to a reference point. Displacement (Δp) is the straight-line change in position — a vector. Velocity is the rate of change of position, and acceleration is the rate of change of velocity. Graphically, velocity is the slope of the position–time curve and acceleration is the slope of the velocity–time curve. Going the other way, the area under a velocity curve is displacement.
| v = (p_f − p_i) / Δt | Average velocity over an interval |
| a = (v_f − v_i) / Δt | Average acceleration over an interval |
| Δp = ∫ v dt | Displacement = area under v–t curve |
| Δv = ∫ a dt | Change in velocity = area under a–t curve |
Three reading rules you will use every week: where position is at a peak or valley, velocity is zero; where velocity is at a peak or valley, acceleration is zero; and when velocity and acceleration have the same sign, the object is speeding up.
2. Phases of the countermovement jump
| Phase | COM displacement | COM velocity | COM acceleration |
|---|---|---|---|
| Quiet standing | Constant (reference = 0) | 0 | 0 |
| Unweighting | Starts to drop | Becoming more negative | Negative |
| Braking | Still dropping, reaches lowest point | Negative → 0 at lowest point | Positive (slowing the fall) |
| Propulsion | Rising to takeoff | Positive, peaks just before takeoff | Positive, falls to ≈ 0 near takeoff |
| Flight | Rises to peak then falls | Decreases linearly; 0 at peak height | ≈ −9.81 m/s² (gravity only) |
| Landing | Drops below standing then returns | Negative → 0 | Large positive spike |
3. Where is the center of mass?
The COM is the point where the body's mass is balanced. In anatomical standing it lies roughly 55–57% of standing height from the floor, near the pelvis, just anterior to the second sacral vertebra (S2). In this lab we approximate COM with a single tracked point at the pelvis. That is a simplification: when the arms swing overhead or the trunk flexes, the true COM moves relative to the pelvis. (In Week 9 you will compute COM properly from body segments.)
4. Capturing video you can analyze
- Camera perpendicular to the plane of motion (side view for sagittal, front view for frontal). Angled cameras shorten distances — perspective error.
- Stationary camera on a tripod at hip height; no zoom or panning during the trial.
- Frame rate ≥ 60 fps (120–240 fps slow-motion is better). Each frame is a time sample; Δt = 1/fps.
- Calibration object in the same plane as the jumper (the subject's measured height or a meter stick placed where they stand).
- Whole body plus jump height in frame for the entire trial, with 2 s of still standing before and after.
5. From positions to velocity: finite differences
Kinovea gives position at discrete times. Excel estimates velocity between consecutive frames: v = (y₂ − y₁)/(t₂ − t₁). Repeat for acceleration using velocity. Each differentiation amplifies small tracking errors, because a 2 mm click error divided by a 1/60 s interval becomes a 0.12 m/s velocity error, and then divided again becomes a 7 m/s² acceleration error. Try it below.
Before you come to lab
- Install Kinovea and open it once to confirm it runs.
- Wear fitted athletic clothing and shoes; you may be a jumper.
- Know your height in meters (or we will measure it).
- Bring a phone that can record at ≥ 60 fps and a charging cable.
Pre-Lab Quiz ≈ 10 min
Short responses (submit to your LMS)
1. Sketch (in words or a quick drawing) what you expect the COM velocity–time curve to look like from quiet standing to landing. Mark where velocity is zero.
2. Using our single-point COM estimate at the pelvis, describe one situation during a CMJ when this estimate would be inaccurate and explain why.
Lab Activity 90 min
Group organization
4 teams of 5. Each team films two jumpers in two views (sagittal and frontal) = 4 videos; with 2 trials each, every student owns one trial to analyze (the arm-swing trial is optional). Roles: Jumper, Camera operator, Calibration/landmark, Timer/caller, Recorder.
Equipment per team
- Phone or camera (≥ 60 fps) + tripod
- Meter stick (calibration), tape measure, stadiometer or wall tape
- Contrasting tape/marker sticker for the pelvis (anterior S2 / greater trochanter level)
- Laptops with Kinovea and Excel
Timeline
- 0:00–0:10Demo: camera placement, calibration and a 2-minute Kinovea tracking walkthrough on the projector.
- 0:10–0:30Part 1 — Video collection. Two filming stations (sagittal and frontal) per team; jumpers rotate between them.
- 0:30–1:15Part 2 — Kinovea. Each student calibrates and tracks their own trial. Goal: export before you leave. If tracking is not finished, complete it after lab (Step 0 of the report, ≈ 15 min).
- 1:15–1:30Part 3 — Excel start. Open your export (or the backup data set if yours is not ready), convert units, make the displacement graph, and get the instructor's check-off.
Part 1 — Video collection
- Measure jumper height (m) and mark the pelvis landmark with tape.
- Set the camera on a tripod at hip height, ~3–4 m away, perpendicular to the plane. Frame the whole body plus ~0.6 m above the head.
- Place the meter stick vertically where the jumper stands; record 2 s of it, then remove it (or use the jumper's height as the calibration).
- Record: jumper stands still 2 s → performs a maximal CMJ (hands on hips for both trials; an extra arm-swing trial is optional) → lands and stands still 2 s.
- Transfer videos to the analyzing student's laptop (AirDrop, email, Teams). Name them
Team#_Jumper_View_Trial.mp4.
Part 2 — Kinovea workflow
- Open the video in Kinovea.
- Calibrate: draw a line from the top of the head to the floor (or along the meter stick), right-click the line → Calibrate, and enter the known length in meters.
- Set the origin (optional but recommended): place the coordinate-system origin at the floor under the jumper so vertical position is height above the floor.
- Place a point marker on the pelvis landmark (estimated COM). Right-click → Track path.
- Step frame by frame through descent, takeoff, flight and landing. Where the automatic tracker drifts (blur at takeoff is common), drag the point back onto the landmark. Consistency beats perfection.
- Export: File → Export → Spreadsheet (Excel or CSV). Save as
LastName_CMJ_View.xlsx.
Lab Report ≈ 90 min
⬇ CMJ COM export, 60 fps, time in s
Submit an Excel workbook and a Word/PDF document with figures and answers. Analyze your own sagittal-plane trial; use a teammate's frontal-plane trial if you answer Optional Question A.
Step 0 — Finish tracking (only if needed) ≤ 15 min
If you did not export in lab, finish tracking your trial in Kinovea and export it. Students whose video failed or who were absent use the backup data set below and skip this step.
Step 1 — Organize the data ≈ 10 min
| Col | Header | Formula (first data row = 3) |
|---|---|---|
| A | Time (s) | from Kinovea (÷1000 if in ms) |
| B | Vertical position y (m) | from Kinovea |
| C | Displacement from standing (m) | =B3-AVERAGE($B$3:$B$30) |
| D | Velocity (m/s) | =(C4-C3)/(A4-A3) |
| E | Acceleration (m/s²) | =(D5-D4)/(A5-A4) |
| F (optional) | Smoothed displacement | =AVERAGE(C3:C7) |
Rows 3–30 should be quiet standing; adjust the range to match your data. Note that velocity starts one row later than displacement and acceleration two rows later.
Step 2 — Graphs ≈ 20 min
For each graph: highlight the time column and the variable → Insert → Scatter with smooth lines. Add a title, axis titles with units, and remove the legend if there is only one series.
- Figure 1. Vertical COM displacement vs. time. Label: start of unweighting, lowest point, takeoff, peak height, landing.
- Figure 2. COM velocity vs. time. Label: peak downward velocity, zero crossing at the lowest point, peak upward velocity.
- Figure 3. COM acceleration vs. time. Shade or label the flight phase.
What a strong figure looks like
Figure 1. Vertical COM displacement (top), velocity (middle) and acceleration (bottom) during a countermovement jump. Backup data set, sagittal view, 60 fps; displacement smoothed with a 5-point moving average before differentiation. Shading marks the jump phases.
Why this earns full credit
- The caption is below the figure, numbered, and says what, who, how (fps, smoothing).
- Every axis has a title with units, and the three charts share one time axis.
- Key events are labeled with their values (lowest point, peak velocity, peak height).
- The quality check is on the figure: flight acceleration ≈ −9.6 m/s² vs. −9.81 expected.
- There are no default legends, no gridline clutter, and no "Series 1".
Common mistakes we see
- Line chart instead of scatter, so time is spaced as categories, not seconds.
- Time left in milliseconds, so velocity comes out 1000× too small.
- Charts with different x-axis ranges, so phases don't line up.
- Acceleration y-axis auto-scaled to ±200 m/s² by one noisy point. Set the bounds manually and say so in the caption.
- Phases or events described in the text but not marked on the graph.
Excel charts look different from this one, and that's fine. Graders look for the elements listed, not for matplotlib styling.
Step 3 — Key values table ≈ 15 min
Create Table 1 with: countermovement depth (m, =MIN(C:C)), peak upward velocity (m/s, =MAX(D:D)), time of takeoff (s), flight time (s), jump height from displacement (peak minus standing, m), jump height from flight time h = g·t²/8, and mean acceleration during flight (m/s², =AVERAGE over flight rows).
Step 4 — Discussion questions ≈ 30 min
Claim: During flight, vertical COM velocity decreased in a nearly straight line from upward to downward.
Evidence: In Figure 1, velocity fell from +2.43 m/s at takeoff (1.80 s) through zero at peak height (2.07 s) to about −2.4 m/s just before landing (2.33 s). The mean acceleration over the flight phase was −9.6 m/s².
Reasoning: Once the feet leave the ground, gravity is the only external force on the body (ignoring air resistance). By Newton's second law, acceleration is constant at about −9.81 m/s², so velocity changes at a constant rate and the v–t graph is a straight line with that slope. My value is about 2% below −9.81 m/s², which suggests my calibration and tracking were reasonable. The small difference is probably tracking error at takeoff, where the video is blurred.
Why it works: it answers the question directly, quotes numbers with units and times from the student's own figure, explains the mechanism with a course principle (Newton's second law), and judges data quality. Aim for this structure — claim, evidence, reasoning — in every answer.
Answer the five required questions. Optional questions earn up to +3 extra-credit points.
- Identify the lowest point of COM displacement. What phase of the CMJ does this represent, and what is the velocity at this instant?
- When is upward velocity greatest, and why does it peak before the feet leave the ground?
- Describe how acceleration changes during (a) descent, (b) takeoff, and (c) flight. Did your mean flight acceleration match −9.81 m/s²? What does the difference tell you about your data quality?
- Explain why your acceleration values appear more variable than displacement. Name two things you could do (during filming or in Excel) to reduce this.
- In your own words, describe how displacement, velocity, and acceleration are related, using one specific moment from your graphs as an example.
Optional questions (extra credit)
- Compare jump height from displacement with jump height from flight time. Which do you trust more and why?
- Using a teammate's frontal-plane video, what can you observe in the frontal plane (e.g., side-to-side COM shift, knee valgus) that the sagittal view hides?
Submission checklist
- Excel workbook with calculations and Figures 1–3.
- Document with Figures 1–3 (labeled phases), Table 1, Discussion Questions 1–5 (plus any optional questions).
- Your video file (or a screenshot of your Kinovea tracking with calibration visible).
Grading rubric (50 pts)
| Criterion | Pts | Full credit looks like |
|---|---|---|
| Data processing | 12 | Correct units, correct finite-difference formulas, standing reference |
| Figures | 12 | Three aligned graphs, titled, axis units, phases labeled |
| Table 1 & quality check | 8 | All values reported; flight acceleration evaluated |
| Discussion questions | 15 | Correct, references your own graphs |
| Presentation | 3 | Clear, professional, consistent decimals |
References
- Urone, P. P., & Hinrichs, R. (2022). College physics 2e. OpenStax. openstax.org (CC BY 4.0) Chapter 2 (kinematics).
- Linthorne, N. P. (2001). Analysis of standing vertical jumps using a force platform. American Journal of Physics, 69(11), 1198–1204. doi.org/10.1119/1.1397460
- Winter, D. A. (2009). Biomechanics and motor control of human movement (4th ed.). Wiley. Chapter 2 (signal processing).
- Puig-Diví, A., Escalona-Marfil, C., Padullés-Riu, J. M., Busquets, A., Padullés-Chando, X., & Marcos-Ruiz, D. (2019). Validity and reliability of the Kinovea program in obtaining angles and distances using coordinates in 4 perspectives. PLOS ONE, 14(6), e0216448. doi.org/10.1371/journal.pone.0216448